IEI Technology IMB-H110 User Manual Download Page 120

Page: 120 / 161

IMB-H110 microATX Motherboard

Page 105

5.3.7.1 Legacy Console Redirection Settings

Advanced

Legacy Serial Redirection Port

[COM1]

Select a COM port to
display redirection of
Legacy OS and Legacy
OPROM Messages.

---------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 14: Legacy Console Redirection Settings

Legacy Serial Redirection Port [COM1]

Use the Legacy Serial Redirection Port option to select a COM port to display redirection

of legacy OS and legacy OPROM messages.

5.3.8 CPU Configuration

Use the

CPU Configuration

menu (

BIOS Menu 15

) to view detailed CPU specifications

or enable the Intel Virtualization Technology.

Summary of Contents for IMB-H110


































































































































































Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands

IEI Technology IMB-H110, User Manual

Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands