IEI Technology IMB-H110 User Manual Download Page 105

Page: 105 / 161

IMB-H110 microATX Motherboard

Page 90

IO=3F8h;

IRQ=3, 4, 11

Serial Port I/O port address is 3F8h and the interrupt

address is IRQ3, 4, 11

IO=2F8h;

IRQ=3, 4, 11

Serial Port I/O port address is 2F8h and the interrupt

address is IRQ3, 4, 11

IO=3E8h;

IRQ=3, 4, 11

Serial Port I/O port address is 3E8h and the interrupt

address is IRQ3, 4, 11

IO=2E8h;

IRQ=3, 4, 11

Serial Port I/O port address is 2E8h and the interrupt

address is IRQ3, 4, 11

IO=2D0h;

IRQ=3, 4, 11

Serial Port I/O port address is 2D0h and the interrupt

address is IRQ3, 4, 11

IO=2E0h;

IRQ=3, 4, 11

Serial Port I/O port address is 2E0h and the interrupt

address is IRQ3, 4, 11

5.3.3.3 Serial Port 2 Configuration

Serial Port [Enabled]

Use the

Serial Port

option to enable or disable the serial port.

Disabled

Disable the serial port

Enabled D

EFAULT

Enable the serial port

Change Settings [Auto]

Use the

Change Settings

option to change the serial port IO port address and interrupt

address.

Auto D

EFAULT

The serial port IO port address and interrupt address

are automatically detected.

IO=2F8h;

IRQ=3

Serial Port I/O port address is 2F8h and the interrupt

address is IRQ3

Summary of Contents for IMB-H110


































































































































































Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands

IEI Technology IMB-H110, User Manual

Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands