IEI Technology IMB-H110 User Manual Download Page 22

Page: 22 / 161

IMB-H110 microATX Motherboard

Page 7

1.6 Technical Specifications

The IMB-H110 technical specifications are listed below.

Specification/Model

IMB-H110

Form Factor

microATX

CPU Supported

6th generation LGA1151 Intel® Core™ i7/i5/i3, Pentium® or

Celeron® CPU

PCH

Intel® H110

Memory

Two 288-pin 2133 MHz dual-channel unbuffered DDR4

SDRAM DIMMs supported (system max. 64 GB)

Graphics Engine

Intel® HD Graphics Gen9 engine with 16 low-power execution

units, supporting DX2015, OpenGL 5.x, OpenCL 2.x and ES 2.0

Display Output

Supports dual independent display

One VGA (Chrontel CH7517)

One DVI-I (TI SN75DP139

Chrontel CH7517)

One LVDS (Chrontel CH7511)

One iDP interface for HDMI, LVDS, VGA, DVI and DisplayPort

Ethernet Controllers

Dual Realtek RTL 8111GN GbE controller

Audio

Realtek ALC662 HD Audio codec supports 5.1 channels

BIOS

AMI UEFI BIOS

Super I/O Controller

Fintek F81866

Watchdog Timer

Software programmable supports 1~255 sec. system reset

Expansions

One PCIe x16 slot (Gen3)

One PCIe x1 slot (Gen2)

Two PCI slots

One full-size/half-size PCIe Mini card slot

Summary of Contents for IMB-H110


































































































































































Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands

IEI Technology IMB-H110, User Manual

Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands