IEI Technology IMB-H110 User Manual Download Page 129

Page: 129 / 161

IMB-H110 microATX Motherboard

Page 114

128M

256M

Default

512M

DVMT Total Gfx Mem [MAX]

Use the

DVMT Total Gfx Mem

option to select DVMT5.0 total graphic memory size used

by the internal graphic device. The following options are available:

128M

256M

MAX

Default

Primary IGFX Boot Display [VBIOS Default]

Use the

Primary IGFX Boot Display

option to select the display device used by the

system when it boots. Configuration options are listed below.

VBIOS

Default

Default

CRT

DVI-VGA

LVDS

DVI

Backlight Control Mode [LED(PWM)]

Use the

Backlight Control Mode

BIOS option to select the LCD backlight control mode.

Configuration options are listed below.

LED(PWM)

EFAULT

CCFL(Linear)

Backlight Control Type [PWM]

Use this BIOS option to select the LCD backlight control type from

PWM

Summary of Contents for IMB-H110


































































































































































Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands

IEI Technology IMB-H110, User Manual

Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands