IEI Technology IMB-H110 User Manual Download Page 104

Page: 104 / 161

IMB-H110 microATX Motherboard

Page 89

5.3.3.1 Serial Port 1 ~ 6 Configuration

Use the

Serial Port 1 ~ 6 Configuration

menu (

BIOS Menu 6

) to configure the serial

ports.

Advanced

Serial Port n Configuration

Serial Port

[Enabled]

Device Settings

IO=3F8h; IRQ=4

Change Settings

[Auto]

Enable or Disable Serial
Port (COM)

---------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 6: Serial Port 1 ~ 6 Configuration Menu

5.3.3.2 Serial Port 1 Configuration

Serial Port [Enabled]

Use the

Serial Port

option to enable or disable the serial port.

Disabled

Disable the serial port

Enabled D

EFAULT

Enable the serial port

Change Settings [Auto]

Use the

Change Settings

option to change the serial port IO port address and interrupt

address.

Auto D

EFAULT

The serial port IO port address and interrupt address

are automatically detected.

IO=3F8h;

IRQ=4

Serial Port I/O port address is 3F8h and the interrupt

address is IRQ4

Summary of Contents for IMB-H110


































































































































































Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands

IEI Technology IMB-H110, User Manual

Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands