IEI Technology HYPER-BW User Manual Download Page 52

Page: 52 / 102

HYPER-BW

Page 41

Step 4:

To remove the SATA cable from the SATA connector, press the clip on the

connector at the end of the cable.

Step 0:

4.4.2

Single RS-232 Cable

The single RS-232 cable consists of one serial port connector attached to a serial
communications cable that is then attached to a D-sub 9 male connector. To install the
single RS-232 cable, please follow the steps below.

Step 1:

Locate the connector

. The location of the RS-232 connector is shown in

Chapter 3

Step 2:

Insert the cable connector

. Insert the connector into the serial port box header.

See Figure 4-3. A key on the front of the cable connectors ensures the

connector can only be installed in one direction.

Figure 4-3: Single RS-232 Cable Installation

Step 3:

Secure the bracket

. The single RS-232 connector has two retention screws

that must be secured to a chassis or bracket.

Step 4:

Connect the serial device

. Once the single RS-232 connector is connected to

a chassis or bracket, a serial communications device can be connected to the

system.

Summary of Contents for HYPER-BW







































































































Search results

Summary of Contents for HYPER-BW

Reviews:

Related manuals for HYPER-BW

Brands by name

Popular brands

IEI Technology HYPER-BW, User Manual

Search results

Summary of Contents for HYPER-BW

Reviews:

Related manuals for HYPER-BW

Brands by name

Popular brands