IEI Technology HYPER-BW User Manual Download Page 71

Page: 71 / 102

HYPER-BW

Page 60

5.3.7

CPU Configuration

Use the

CPU Configuration

menu (

BIOS Menu 5

) to view detailed CPU specifications

and configure the CPU.

Advanced

CPU Configuration

Intel(R) Pentium(R) CPU N3710 @ 1.60GHz

CPU Signature

406C4

Microcode Patch

408

Max CPU Speed

1600 MHz

Min CPU Speed

480 MHz

Processor Cores

Intel HT Technology

Not Supported

Intel VT-x Technology

Supported

L1 Data Cache

24 KB x 2

L1 Code Cache

32 KB x 2

L2 Cache

1024 KB x 1

L3 Cache

Not Present

64-bit

Supported

Intel Virtualization Technology [Enabled]

EIST [Enabled]

CPU C state Report [Disabled]

When enabled, a VMM can

utilize the additional

hardware capabilities

provided by Vanderpool

Technology.

----------------------



: Select Screen

↑

↓

: Select Item

Enter Select

F1 General Help

F2 Previous Values

Optimized

Defaults

Save

ESC Exit

BIOS Menu 12: CPU Configuration



Intel® Virtualization Technology [Dis abled]

Use the

Intel® Virtualization Technology

option to enable or disable virtualization on the

system. When combined with third party software, Intel Virtualization technology allows
several OSs to run on the same system at the same time.



Disabled

EFAULT

Disables Intel Virtualization Technology.



Enabled

Enables Intel Virtualization Technology.



EIST [Enabled]

Use the

EIST

option to enable or disable the Intel Speed Step Technology.

Summary of Contents for HYPER-BW







































































































Search results

Summary of Contents for HYPER-BW

Reviews:

Related manuals for HYPER-BW

Brands by name

Popular brands

IEI Technology HYPER-BW, User Manual

Search results

Summary of Contents for HYPER-BW

Reviews:

Related manuals for HYPER-BW

Brands by name

Popular brands