IEI Technology HYPER-BW User Manual Download Page 78

Page: 78 / 102

HYPER-BW

Page 67

5.4.2

Southbridge Configuration

Use the

Southbridge Configuration

menu (

BIOS Menu 18

) to configure the Southbridge

chipset.

Chipset

> PCI Express Configuration

Auto Power Button Status

[Enabled(AT)]

Audio Configuration

Audio Controller

[Enabled]

Azalia HDMI Codec

[Enabled]

XHCI Mode

[Enabled]

PCI Express

Configuration settings.

---------------------



: Select Screen

↑

↓

: Select Item

Enter Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

BIOS Menu 18: Southbridge Chipset Configuration



Audio Controller [Enabled]

Use the

Audio

Controller

option to enable or disable the High Definition Audio controller.



Disabled

The onboard High Definition Audio controller is disabled



Enabled D

EFAULT

The onboard High Definition Audio controller is detected
automatically and enabled



Azalia HDMI codec [Enabled]

Use the

Azalia HDMI codec

option to enable or disable the HDMI codec for High

Definition Audio.



Disabled

Disable HDMI codec for High Definition Audio



Enabled

EFAULT

Enable HDMI codec for High Definition Audio

Summary of Contents for HYPER-BW







































































































Search results

Summary of Contents for HYPER-BW

Reviews:

Related manuals for HYPER-BW

Brands by name

Popular brands

IEI Technology HYPER-BW, User Manual

Search results

Summary of Contents for HYPER-BW

Reviews:

Related manuals for HYPER-BW

Brands by name

Popular brands