manualshive.com logo in svg

IEI Technology HYPER-BW, User Manual

Share
Download
IEI Technology HYPER-BW User Manual Download Page 63

 

 

HYPER-BW 

 

Page  52 

5.3.3.1

 

Smart Fan Mode Configuration 

Use the 

Smart  Fan Mode  Configuration submenu

  (

BIOS Menu 7

)  to configure fan 

temperature and speed settings. 

Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

Smart Fan Mode Configuration 

 

CPU Smart Fan control 

[Auto PWM Mode] 

Temperature of Off 

75 

Temperature of Start 

80 

Start PWM 

30 

Slope(Duty Cycle) 

[4] 

 

 

CPU Smart Fan control 

settings. 

 

 

 

--------------------- 



: Select Screen 

↑

 

↓

: Select Item 

Enter Select 

+ -   Change Opt. 

F1  General Help 

F2  Previous Values 

F3  Optimized Defaults 

F4  Save & Exit 

ESC  Exit 

Version 2.17.1249. Copyright (C) 2016 American Megatrends, Inc. 

BIOS Menu 7: Smart Fan Mode Configuration

 

 

CPU Smart Fan control [Auto PWM Mode] 

Use the 

CPU Smart Fan control

 BIOS option to configure the CPU Smart Fan.   

 

Full Mode 

 

Fan is on all the time 

 

Manual PWM Mode     

The fan spins at the speed set in the manual 
PWM setting 

 

Auto PWM Mode 

D

EFAULT

 

The fan adjusts its speed using these 
settings: 

    Temperature of Off 

Temperature of Start 

   Start PWM 

   Slope (Duty Cycle) 

Summary of Contents for HYPER-BW







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands