manualshive.com logo in svg

IEI Technology HYPER-BW, User Manual

Share
Download
IEI Technology HYPER-BW User Manual Download Page 74

 

 

HYPER-BW 

Page  63 

does not become available until a USB compatible operating system is fully booted with all 
USB drivers loaded. When this option is enabled, any attached USB mouse or USB 
keyboard can control the system even when there is no  USB driver loaded onto the 
system.   

 

Enabled 

D

EFAULT

 

Legacy USB support enabled 

 

Disabled 

 

Legacy USB support disabled 

 

Auto 

 

Legacy USB support disabled if no USB devices are 
connected 

5.4

 

Chips et 

Use the 

Chipset

  menu (

BIOS Menu 15

) to access the Northbridge and Southbridge 

configuration menus 

  WARNING! 

Setting the wrong values for the Chipset BIOS selections in the Chipset 
BIOS menu may cause the system to malfunction. 

 

Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. 

Main 

Advanced 

Chipset 

Security 

Boot  Save & Exit 

 

> North Bridge 

> South Bridge 

 

 

North Bridge Parameters 

 

 

--------------------- 



: Select Screen 

↑

 

↓

: Select Item 

Enter Select 

+/-:  Change Opt. 

F1  General Help 

F2  Previous Values 

F3  Optimized Defaults 

F4  Save & Exit 

ESC  Exit 

Version 2.17.1249. Copyright (C) 2016 American Megatrends, Inc. 

BIOS Menu 15: Chipset

 

Summary of Contents for HYPER-BW







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands