IEI Technology AFL-xxA-N270 series User Manual Download Page 86

Page: 86 / 171

AFL-xxA-N270 Series Panel PC

Page 71

The CPU Configuration menu (

BIOS Menu 3

) lists the following CPU details:

Manufacturer

: Lists the name of the CPU manufacturer

Brand String

: Lists the brand name of the CPU being used

Frequency:

Lists the CPU processing speed

FSB Speed

: Lists the FSB speed

Cache L1

: Lists the CPU L1 cache size

Cache L2

: Lists the CPU L2 cache size

6.3.2 IDE Configuration

Use the

IDE Configuration

menu (

BIOS Menu 4

) to change and/or set the configuration

of the IDE devices installed in the system.

BIOS Menu 4: IDE

Configuration

ATA/IDE Configurations [Compatible]

Use the

ATA/IDE Configurations

option to configure the ATA/IDE controller.

Disabled

Disables the on-board ATA/IDE controller.

Compatible D

EFAULT

Configures the on-board ATA/IDE controller to be in

Summary of Contents for AFL-xxA-N270 series












































































































































































Search results

Summary of Contents for AFL-xxA-N270 series

Reviews:

IEI Technology AFL-xxA-N270 series, User Manual, Page: 86 / 171

Search results

Summary of Contents for AFL-xxA-N270 series

Reviews: