manualshive.com logo in svg

IEI Technology AFL-xxA-N270 series, User Manual, Page: 58 / 171

Share
Download
IEI Technology AFL-xxA-N270 series User Manual Download Page 58

 

 

AFL-xxA-N270 Series Panel PC 

Page 43 

4.9.7 COM3 RS-232/422/485 Serial Port Select Jumper 

Jumper Label: 

JP6 

Jumper Type: 

12-pin header (four 3-pin headers combined) 

Jumper Settings: 

See 

Table 4-10

 

Jumper Location: 

See 

Figure 4-11

 

The COM3 RS-232/422/485 Serial Port Select jumper sets the communication protocol 

used by the second serial communications port (COM3) as RS-232, RS-422 or RS-485. 

The COM3 RS-232/422/485 Serial Port Select settings are shown in 

Table 4-10

. 

RS-232/485 Select 

Description 

 

Short 1-2 

RS-232 

Default 

Short 4-5 

RS-232 

Default 

Short 7-8 

RS-232 

Default 

Short 10-11 

RS-232 

Default 

Short 2-3 

RS-422/485 

 

Short 5-6 

RS-422/485 

 

Short 8-9 

RS-422/485 

 

Short 11-12 

RS-422/485 

 

Table 4-10: COM3 RS-232/422/485 Serial Port Select Jumper Settings 

The COM3 RS-232/422/485 Serial Port Select jumper location is shown in 

Figure 4-11

. 

Summary of Contents for AFL-xxA-N270 series












































































































































































Reviews:

No comments