IEI Technology AFL-xxA-N270 series User Manual Download Page 65

Page: 65 / 171

AFL-xxA-N270 Series Panel PC

Page 50

Figure 4-19: Tighten the Panel Mounting Clamp Screws

4.10.3 Arm Mounting

The AFL-xxA-N270 series is VESA (Video Electronics Standards Association) compliant

and can be mounted on an arm with a 75mm or 100mm interface pad. To mount the

AFL-xxA-N270 series on an arm, please follow the steps below.

Step 15:

The arm is a separately purchased item. Please correctly mount the arm onto

the surface it uses as a base. To do this, refer to the installation documentation

that came with the mounting arm.

NOTE:

When purchasing the arm please ensure that it is VESA compliant and that

the arm has a 75 mm interface pad. If the mounting arm is not VESA

compliant it cannot be used to support the AFL-xxA-N270 series flat panel

PC. The AFL-10A-N270 and AFL-12A-N270 also support VESA MIS-D

100.

Summary of Contents for AFL-xxA-N270 series












































































































































































Search results

Summary of Contents for AFL-xxA-N270 series

Reviews:

IEI Technology AFL-xxA-N270 series, User Manual, Page: 65 / 171

Search results

Summary of Contents for AFL-xxA-N270 series

Reviews: