manualshive.com logo in svg

IEI Technology AFL-xxA-N270 series, User Manual, Page: 37 / 171

Share
Download
IEI Technology AFL-xxA-N270 series User Manual Download Page 37

 

 

AFL-xxA-N270 Series Panel PC

Page 22 

2.8 Wireless Connections 

The following section describes the wireless modules on the circuit. 

2.8.1 USB Bluetooth Module 

An integrated Bluetooth module is connected to ICH7 chipset through the USB bus. The 

AFL-xxA-N270 Bluetooth module enables wireless communications between the 

AFL-xxA-N270 and various peripheral devices through a Bluetooth network. The 

peripheral devices may include: 

 Headsets 

 Barcode 

readers 

 PDA 

 Printers 

 Cell 

phones 

  Keyboard and mouse 

The technical specifications of the Bluetooth module are listed in the Appendix. 

2.8.2 Wireless Ethernet 

An integrate PIFA antenna on the AFOLUX AFL-xxA-N270 ensures an uninterrupted 

wireless connection. PIFA antennas can receive high-quality, uniform signals in any 

location from all directions without any signal degradation or impedance and are the most 

efficient antennas on the market. 

Summary of Contents for AFL-xxA-N270 series












































































































































































Reviews:

No comments