IEI Technology AFL-xxA-N270 series User Manual Download Page 166

Page: 166 / 171

AFL-xxA-N270 Series Panel PC

Page 151

E.1 Hazardous Material Disclosure Table for IPB Products

Certified as RoHS Compliant Under 2002/95/EC Without
Mercury

The details provided in this appendix are to ensure that the product is compliant with the

Peoples Republic of China (China) RoHS standards. The table below acknowledges the

presences of small quantities of certain materials in the product, and is applicable to China

RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly

Use Period” (EFUP). This is an estimate of the number of years that these substances

would “not leak out or undergo abrupt change.” This product may contain replaceable

sub-assemblies/components which have a shorter EFUP such as batteries and lamps.

These components will be separately marked.

Please refer to the table on the next page.

Summary of Contents for AFL-xxA-N270 series












































































































































































Search results

Summary of Contents for AFL-xxA-N270 series

Reviews:

IEI Technology AFL-xxA-N270 series, User Manual, Page: 166 / 171

Search results

Summary of Contents for AFL-xxA-N270 series

Reviews: