manualshive.com logo in svg

IEI Technology AFL-xxA-N270 series, User Manual, Page: 106 / 171

Share
Download
IEI Technology AFL-xxA-N270 series User Manual Download Page 106

 

 

AFL-xxA-N270 Series Panel PC 

Page 91 

 

USB Functions [Enabled] 

Use the 

USB Function

 option to enable or disable the USB controllers. 

 

Disabled  

USB controllers are enabled 

 

Enabled D

EFAULT

 

USB controllers are disabled 

 

USB 2.0 Controller [Enabled] 

The 

USB 2.0 Controller

 BIOS option enables or disables the USB 2.0 controller   

 

Enabled D

EFAULT

 

USB function enabled 

 

Disabled  

USB function disabled 

 

Legacy USB Support [Enabled] 

Use the 

Legacy USB Support

 BIOS option to enable USB mouse and USB keyboard 

support.  

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not 

become available until a USB compatible operating system is fully booted with all USB 

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard 

can control the system even when there is no USB driver loaded onto the system.   

 

Disabled 

 

Legacy USB support disabled 

 

Enabled D

EFAULT

 

Legacy USB support enabled 

 

Auto  

Legacy USB support disabled if no USB devices are 

connected 

 

USB2.0 Controller Mode [HiSpeed] 

The 

USB2.0 Controller Mode

 BIOS option sets the speed of the USB2.0 controller.   

 

FullSpeed  

The controller is capable of operating at full speed 

12 Mb/s 

Summary of Contents for AFL-xxA-N270 series












































































































































































Reviews:

No comments