Command Sub command
00
—
01
Same as
command 06
02
—
03
—
04
—
05
—
00
06
01
03
04
—
00
01
07
A0
B0
D0
D1
—
01–0106*
08
09
—
0A
—
0B
—
0C
—
0D
—
00
0E
01
D0
D3
00
01
0F
10
11
12
00
01
02
03
04
10
05
06
07
08
09
10
11
11
00
10, 20, 30
00
13
01
02
Description
Send frequency data for trans-
ceive.
Send mode data for transceive.
Read band edge frequencies.
Read operating frequency data.
Read operating mode data.
Set operating frequency.
Set LSB.
Set USB.
Set CW.
Set FM.
Select VFO mode.
Select VFO A.
Select VFO B.
Equalize VFO A and VFO B.
Switch VFO A and VFO B.
Select MAIN VFO.
Select SUB VFO.
Select memory mode.
Select memory channel.
* 1A=0100
1b=0101
2A=0102
2b=0103
3A=0104
3b=0105
Call=0106
Memory write.
Transfer memory contents to
VFO.
Memory clear.
Read duplex offset frequency.
Set duplex offset frequency.
Cancel scan.
Start scan.
Set scan resume OFF.
Set scan resume ON.
Turn the split function OFF.
Turn the split function ON.
Set simplex operation.
Set DUP– operation.
Set DUP+ operation.
Set 1 Hz tuning step.
Set 10 Hz tuning step.
Set 50 Hz tuning step.
Set 100 Hz tuning step.
Set 1 kHz tuning step.
Set 5 kHz tuning step.
Set 6.25 kHz tuning step.
Set 10 kHz tuning step.
Set 12.5 kHz tuning step.
Set 20 kHz tuning step.
Set 25 kHz tuning step.
Set 100 kHz tuning step.
Turn attenuator OFF.
Turn attenuator ON.
Announce all S-meter levels, dis-
played frequency and mode.
Announce displayed frequency.
Announce operating mode.
79
13
CONTROL COMMAND
Command Sub command
01
02
03
04
06
14
09
0A
0B
0C
0E
0F
01
15
02
02
12
22
40
+level data
41
16
42
43
44
46
47
4A
19
00
00
01
02
+level data
03
+level data
04
1A
+level data
05
+level data
06
07
08
09
00
1B
01
1C
00
Description
[AF] level setting (0=max. CCW;
128=center; 255=max. CW).
[RF GAIN] level setting
(0=max. CCW; 255=max. CW).
[SQL] level setting (0=max.
CCW; 255=max. CW).
[IF SHIFT] level setting (0=max.
CCW; 128=center; 255=max. CW).
Set noise reduction level (0=0%;
255=100%).
Set CW pitch (0=300 Hz;
255=900 Hz).
[RF PWR] level setting (0=max.
CCW; 128=center; 255=max. CW).
[MIC GAIN] level setting (0=max.
CCW; 128=center; 255=max. CW).
Key speed setting (0=6 wpm;
255=60 wpm).
Set mic. compressor level
(0=0%; 255=100%).
Set break-in delay (0=2.0 sec;
255=13.0 sec.).
Read squelch condition (open or
closed).
Read S-meter level.
Set pre-amp (0=OFF; 1=ON).
Set AGC (0=Slow; 1=Fast).
Set noise blanker (0=OFF; 1=ON).
Set noise reduction level
(0=OFF; 1–15=ON).
Set auto notch filter
(0=OFF; 1=ON).
Set subaudible tone
(0=OFF; 1=ON).
Set tone squelch (0=OFF; 1=ON).
Set mic. compressor
(0=OFF; 1=ON).
Set VOX (0=OFF; 1=ON).
Set break-in (0=OFF; 1=ON).
Set AFC (0=OFF; 1=ON).
Read the transceiver ID.
Read/write memory channel.
Set satellite memory.
Set VOX gain level
(0=0%; 255=100%).
Set VOX delay
(0=0 sec.; 20=2.0 sec.).
Set anti-VOX
(0=0%; 255=100%).
Attenuation level setting
(0=0%; 255=100%).
Set RIT (0=OFF; 1=ON; 2=Sub dial).
Set satellite mode (0=OFF; 1=ON).
Set simple bandscope
(0=OFF; 1=ON).
Set sub band (0=OFF; 1=ON)
Set subaudible tone frequency
(67 Hz=000670 to 254.1 Hz=002541)
Set tone squelch frequency
(67 Hz=000670 to 254.1 Hz=002541)
Set/read transceiver’s condition
(0=Rx; 1=Tx)
Summary of Contents for IC-910H
Page 1: ...INSTRUCTION MANUAL VHF UHF ALL MODE TRANSCEIVER i910H ...
Page 86: ...84 MEMO ...
Page 87: ...85 MEMO ...