manualshive.com logo in svg

Icom AP-90M, Instruction Manual

Share
Download
Icom AP-90M Instruction Manual Download Page 85

6

MAINTENANCE

6-11

 Naming the automatic setting files

 Name the setting file “savedata” (format: sav) on the USB flash drive.

•  You can only use the setting file saved in the “Save to File” setting on the “Setting Backup/Restore” screen 

in the “Management” menu. (

+

p.6-2)

Name the firmware file “firmware” (format: dat) on the USB flash drive.

•  Download the firmware file to use for the automatic firmware update from the Icom website and decom

-

press the file. Then name the file “firmware.”

 Automatic setting backups

 A total of 10 latest setting data files can be automatically backed up in the following naming manner.

The latest setting backup data file is automatically named “bakdata.sav.”
  Example: 

The second latest is named “bakdata_1.sav.”

       

The third latest is named “bakdata_2.sav.”

•  If the number of backups exceeds 10, the oldest setting backup file (bakdata_10.sav) is deleted, and each number 

shifts to one higher number. (Example: “bakdata_9.sav” shifts to “bakdata_10.sav”)

• Firmware files are not backed up.
• The setting file (bakdata.sav) is automatically backed up when you change a setting in the AP-90M.

5. Automatic setting using a USB flash drive (Continued)

(

+

Continued on the next page)

Summary of Contents for AP-90M








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands