manualshive.com logo in svg

Icom AP-90M, Instruction Manual

Share
Download
Icom AP-90M Instruction Manual Download Page 58

4

CONNECTING WIRELESS LAN (ADVANCED)

4-7

3. Setting the MAC Authentication Server (RADIUS) (Continued)

Select [Enable] for “MAC Authentication.” 

(Default: Disable)

2

Click [Wireless Settings] and [Wireless1], and then click [Virtual AP].

1

Click [Wireless Settings] and [Wireless1], and then click [Authentication Server].

3

q

 Select

w

 Click

q

 Enter

w

 Click

Wireless Settings > Wireless 1/Wireless 2 > Virtual AP

Wireless Settings > Wireless 1/Wireless 2 > Authentication Server

 Setting the Virtual APs together

Setting all the virtual APs together on the Wireless 1 is used as an example.

4

Enter the RADIUS server data.

• Depending on the system you use, the port number may differ from the default settings.
• Set the same password for the AP-90M in “Secret” for the primary and secondary RADIUS servers.

Click [Reboot].

• Follow the instructions to reboot the AP-90M.

5

After the reboot is complete, click [Back].

6

Click

Summary of Contents for AP-90M








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands