manualshive.com logo in svg

Icom AP-90M, Instruction Manual

Share
Download
Icom AP-90M Instruction Manual Download Page 3

INTRODUCTION

Form2001

ii

 About the wireless LAN standards

The AP-90M’s wireless LAN standards and the maximum communication rates are shown in the table 
below.

Frequency band

Wireless LAN standard

Bandwidth*

Maximum communication rate 

(theory)

5 G

Hz

IEEE802.11ac

80 MHz

867 Mbps

40 MHz

400 Mbps

20 MHz

173 Mbps

IEEE802.11n

40 MHz

300 Mbps

20 MHz

144 Mbps

IEEE802.11a

54 Mbps

2.4 GHz

IEEE802.11n

40 MHz

300 Mbps

20 MHz

144 Mbps

IEEE802.11g

54 Mbps

IEEE802.11b

11 Mbps

Frequency band

Wireless LAN standard

Indoor

Outdoor*

5 GHz

IEEE802.11ac

Approximately

30 m; 32 yd

Approximately
100 m; 109 yd

IEEE802.11n

IEEE802.11a

2.4 GHz

IEEE802.11n

Approximately

30 m; 32 yd

Approximately
100 m; 109 yd

IEEE802.11g

IEEE802.11b

About the Wireless LAN information

•  The maximum communication rate is written based on the maximum theoretical rate of the IEEE802.11 wire

-

less LAN standard, and is not the actual data communication rate.

•  The actual data communication rate differs, depending on the condition in which the AP-90M is used, such as 

distance, obstacles, PC specifications, network vacancy, and so on.

The AP-90M’s wireless LAN standards and the maximum communication distance is shown in the table 
below.

The wireless communication distance differs, depending on the installed location or the frequencies used.
Refer to the table below as a reference.

* The bandwidth that can be used differs, depending on the country.

* Use this product outdoors according to your local regulations.

Summary of Contents for AP-90M








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands