Ice 18ZR Operation And Maintenance Manual Download Page 41

Page: 41 / 86

Section 6: MAINTENANCE Page

OM-ZR-May15

Vibrator Gear Case

Checking Oil Level:

Check oil level in sight glass located on the lower center of the vibrator gear case. Oil level should be in the

middle of the sight glass.

Adding Oil:

On the vibrator gear case top plate, remove the 1" pipe plug to add oil.

Draining Oil:

Remove ¾” pipe plug at either end of the gear case base plate. Tilt the case for complete drainage.

Power Unit Pump Drive Adapter (350G & 350GZ only)

Checking Oil Level:

Check oil level using the dipstick mounted on the pump drive adapter.

Adding Oil:

Add oil by removing the vent fitting from the top of the pump drive adapter.
of the pump drive adapter.

Draining Oil:

Remove the drain plug on the bottom of the pump drive adapter.

Sight Glass

Drain Plug

Fill Plug

Drain Plug

Vent Fitting

Dip Stick Oil Gauge

Summary of Contents for 18ZR























































































Search results

Summary of Contents for 18ZR

Reviews:

Brands by name

Popular brands

Ice 18ZR, Operation And Maintenance Manual

Search results

Summary of Contents for 18ZR

Reviews:

Brands by name

Popular brands