manualshive.com logo in svg

Ice 18ZR, Operation And Maintenance Manual

Share
Download
Ice 18ZR Operation And Maintenance Manual Download Page 32

Section 5: OPERATION                                                                                Page 30                                                                                          

     OM-ZR-May15

When the engine is warmed-up and the temperature of the hydraulic oil exceeds 75°F (24°C), full speed       

operation may begin. Adjust the throttle so that the engine is running at the high idle rpm indicated below.   

The engine should maintain the full load rpm indicated below under load. 

Power Unit 

Vibrator 

High Idle  Full Load 

Low Idle 

350GZ 18ZR 1950 

1850 

700 

450GZ 18ZR/25ZR 2100 

2000 

700 

595GZ 25ZR 1850 

1750 

700 

700Gz 50ZR 

1800 

1700 

700 

800GZ 50ZR 1800 

1700 

700 

Hydraulic oil temperature is monitored by the Hydraulic Oil Temperature Switch (TS2).  Hydraulic oil 
temperature should never exceed 175

o

F (80

o

C).  If hydraulic oil temperature exceeds 175

o

F (80

o

C), the engine 

will be automatically shut down by the Hydraulic Oil Temperature Switch and the HYD. OIL TEMP. HIGH light 
will be turned on. 

!WARNING – Equipment!

 

Operation of the equipment with hydraulic oil above 175°F (80°C) may result in 
damage to hydraulic components. 

Full Speed Operation 

  1.  Stop the vibrator by turning the MAIN (REV-OFF-FOR) switch to OFF. 

  2.  If the engine has not been warmed up, the engine may be shut down without a cool-down period.   
       Turn the ENGINE POWER switch to OFF. 

  3.  If the engine has been warmed up (running at above 185

o

F [85

o

C] for 15 minutes or more), the engine 

       should be cooled down before shut-down. 
       a.  If the engine has not been idled down, reduce engine rpm to 1200 for 2 minutes, then reduce 
            to 700 for 2 more minutes.   
       b.  If the engine has been idled down, increase engine rpm to 1200 for 2 minutes, then reduce 
            to 700 for 2 more minutes.   
       c.  After the 4-minute cooling period, turn the ENGINE POWER switch to OFF. 

   

Engine Shutdown 

Emergency Stop 

In an emergency, the engine and vibrator may be stopped by pushing the EMERGENCY STOP button on either 
the control pendant or the control panel. 

Engine shutdown may cause hydraulic clamp to open. 

Use the emergency stop button only in actual emergencies as the required engine  
cool-down period is eliminated. 

!WARNING – Safety! 

!WARNING – Equipment! 

Summary of Contents for 18ZR























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands