manualshive.com logo in svg

Ice 18ZR, Operation And Maintenance Manual

Share
Download
Ice 18ZR Operation And Maintenance Manual Download Page 20

Section 4: PREPARATION FOR OPERATION                                                    Page 18                                                                                             

 OM-ZR-May15 

 

Connecting Vibrator Hoses to Power Unit 

The vibrator’s interconnecting hoses (in the bundle) terminate with quick disconnect couplers specific to each  
function and mating quick disconnect at the power unit.  Use care to connect couplers straight and screw  
together completely.  Should quick disconnects or hoses require replacement, use care not to mix up the  
connectors and hose routing.  

Eccentric Moment Actuator 

 Open Clamp 

Motor Return 

Motor Pressure   

Motor Case Drain 

 Close Clamp 

Gear Oil to Vibro 

350GZ Quick Disconnect  Panel 

The vibrator and hydraulic clamp are connected to the power unit by seven hydraulic hoses.  The functions are 
listed above on the corresponding quick disconnect couplers.   

The hoses connect to the power unit with quick-disconnect couplers. Hose couplers are arranged to insure cor-
rect connections at the power unit . 

Clean couplers with a lint-free cloth before making connections. 

Make sure that the couplers are fully run up and hand tightened prior to using an appropriate chain type 
wrench. 

Power unit must be shut down during connection of hydraulic hoses. 
Improper hose connections can cause ruptured hoses or damaged components and poor 
equipment performance. 

!WARNING – Safety! 

!WARNING – Equipment! 

Gear Oil to Cooler 

Summary of Contents for 18ZR























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands