IBM ThinkPad TransNote Hardware Maintenance Manual Download

Page: 46 / 150

Symptom or error

FRU or action, in sequence

0190
Critical low battery error.

1. Charge the battery pack.
2. Battery pack.

0200
Hard disk error — The hard
disk is not working.

1. Reseat the hard-disk

drive.

2. Load Setup Defaults in IBM

BIOS Setup Utility.

3. Hard-disk drive.
4. System board.

021x
Stuck key — Keyboard error.

Run interactive tests of the
keyboard and the auxiliary
input device.

0220
Monitor type error — Monitor
type does not match the one
specified in CMOS.

Load Setup Defaults in IBM
BIOS Setup Utility.

0230
Shadow RAM error — The
shadow RAM failure at offset
nnnn.

System board.

0231
System RAM error — System
RAM failure at offset nnnn.

1. DIMM.
2. System board.

0232
Extended RAM error —
Extended RAM failure at offset
nnnn.

1. DIMM.
2. System board.

0250
System battery error — System
battery is dead.

Replace the backup battery
and run IBM BIOS Setup
Utility to reset the time and
date.

0251
System CMOS checksum bad
— Default configuration used.

Reconfigure the settings by
running IBM BIOS Setup
Utility.

0252
Password checksum bad —
The password is cleared.

Reset the password by
running IBM BIOS Setup
Utility.

0260
System timer error.

1. Replace the backup

battery and run IBM BIOS
Setup Utility to reset the
time and date.

2. System board.

0270
Real-time clock error.

1. Replace the backup

battery and run IBM BIOS
Setup Utility to reset the
time and date.

2. System board.

0271
Date and time error — Neither
the date nor the time is set in
the computer.

Run IBM BIOS Setup Utility to
reset the time and date.

(continued)

Symptom-to-FRU index

ThinkPad TransNote

Summary of Contents for ThinkPad TransNote























































































































































Search results

Summary of Contents for ThinkPad TransNote

Reviews:

Related manuals for ThinkPad TransNote

Brands by name

Popular brands

IBM ThinkPad TransNote, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkPad TransNote

Reviews:

Related manuals for ThinkPad TransNote

Brands by name

Popular brands