manualshive.com logo in svg

IBM ThinkPad TransNote, Hardware Maintenance Manual

Share
Download
IBM ThinkPad TransNote Hardware Maintenance Manual Download Page 48

Error messages

Symptom or error

FRU or action, in sequence

Device address conflict.

1. Load Setup Defaults in

IBM BIOS Setup Utility.

2. Backup battery.
3. System board.

Allocation error for device.

1. Load Setup Defaults in

IBM BIOS Setup Utility.

2. Backup battery.
3. System board.

Failing bits: nnnn.

1. DIMM.
2. System board.

Invalid system configuration
data.

1. DIMM.
2. System board.

I/O device IRQ conflict.

1. Load Setup Defaults in

IBM BIOS Setup Utility.

2. Backup battery.
3. System board.

Operating system not found.

1. Check that the operating

system has no failure and
is installed correctly.

2. Enter IBM BIOS Setup

Utility and see whether the
hard-disk drive and the
diskette drive are properly
identified.

3. Reseat the hard-disk drive.
4. Reinstall the operating

system.

5. If the diskette drive is

connected and the
operating system is located
on/in the drive, replace the
diskette drive.

6. Hard-disk drive.
7. System board.

Hibernation error.

1. Restore the system

configuration to what it
was before the computer
entered hibernation mode.

2. If memory size has been

changed, re-create the
hibernation file.

Fan error.

Fan.

Symptom-to-FRU index

44

ThinkPad TransNote

Summary of Contents for ThinkPad TransNote























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands