![background image](http://html1.mh-extra.com/html/ibm/thinkpad-transnote/thinkpad-transnote_hardware-maintenance-manual_607196057.webp)
Removing and replacing a FRU
This section presents information and drawings for use in
removing and replacing a FRU. Be sure to observe the
following general rules:
1. Do not try to service the computer unless you have
been trained and certified. An untrained person runs
the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement
notices” on page 50.
3. Begin by removing any FRUs that have to be removed
before the failing FRU. Any such FRUs are listed at the
top of the page. Remove them in the order in which
they are listed.
4. Follow the correct sequence in the steps for removing
the FRU, as indicated in the drawings by the numbers
in square callouts.
5. When turning a screw to replace a FRU, turn it in the
direction indicated by the arrow in the drawing.
6. When removing the FRU, move it in the direction
indicated by the arrow in the drawing.
7. To put the new FRU in place, reverse the removal
procedure and follow any notes that pertain to
replacement. For information about connecting and
arranging internal cables, see “Locations” on page 133.
8. When replacing a FRU, use the correct screw as
shown in the procedures.
CAUTION:
Before removing any FRU, power off the computer,
unplug all power cords from electrical outlets, remove
the battery pack, and then disconnect any
interconnecting cables.
CAUTION:
Do not disassemble the battery pack, throw it into fire
or water, or short-circuit it. Dispose of the battery pack
as required by local ordinances or regulations.
Attention: Before the computer is powered on after FRU
replacement, make sure all screws, springs, and other
small parts are in place and are not loose inside the
computer. Verify this by shaking the computer gently and
listening for rattling sounds. Metallic parts or metal flakes
can cause electrical short circuits.
Attention: The system board is sensitive to, and can be
damaged by, electrostatic discharge. Establish personal
grounding by touching a ground point with one hand before
touching these units.
You must use an electrostatic discharge (ESD) strap (P/N
6405959) to establish personal grounding.
Removing and replacing a FRU
ThinkPad TransNote
53
Summary of Contents for ThinkPad TransNote
