IBM H SERIES RS/6000 User Manual Download Page 35

Page: 35 / 290

Emergency Eject

Note: Execute the following procedure only in an emergency (tray will not eject
although pressing the unload button).

1. Insert a small diameter rod, such as a straightened paper clip, into the emer-

gency eject hole. (Refer to the illustration below for the location of the emergency
eject hole.)

2. Push the tool in until you feel resistance.

3. Maintain a small amount of pressure on the rod while pulling on the tray with

your fingernail.

4. Pull the tray open and remove the disc.

Tray Opening

Emergency

Eject Access

Load/Unload

Button

Status Light

Volume Control

Head Phone

Jack

Note: Normally the tray makes a ratcheting sound when pulling it open using the
above procedure.

Chapter 2. Using the System Unit

2-15

Summary of Contents for H SERIES RS/6000



































































































































































































































































































Search results

Summary of Contents for H SERIES RS/6000

Reviews:

Related manuals for H SERIES RS/6000

Brands by name

Popular brands

IBM H SERIES RS/6000, User Manual

Search results

Summary of Contents for H SERIES RS/6000

Reviews:

Related manuals for H SERIES RS/6000

Brands by name

Popular brands