IBM H SERIES RS/6000 User Manual Download Page 229

Page: 229 / 290

Step 16

This step loads the Standalone Diagnostics. If you are unable to load the diagnos-
tics, go to “Step 7.”

1. Turn the power on.

2. Insert the diagnostic CD-ROM disc into the CD-ROM drive.

3. When the keyboard indicator appears, press F5 on the direct attached keyboard

or 5 on the ASCII keyboard to indicate that diagnostics are to be loaded.

4. Enter requested passwords.

5. Follow instructions to select a console.

Did the Diagnostics Operating Instructions display without any obvious display
problem?

Go to “Step 7.”

YES

Go to “Step 9.”

Step 17

The diagnostics did not find a hardware problem. If you still have a problem, contact
your software support center.

Chapter 9. Hardware Problem Determination

9-9

Summary of Contents for H SERIES RS/6000



































































































































































































































































































Search results

Summary of Contents for H SERIES RS/6000

Reviews:

Related manuals for H SERIES RS/6000

Brands by name

Popular brands

IBM H SERIES RS/6000, User Manual

Search results

Summary of Contents for H SERIES RS/6000

Reviews:

Related manuals for H SERIES RS/6000

Brands by name

Popular brands