IBM Elastic Storage System 3200 Hardware Planning And Installation Manual Download Page 72

Page: 72 / 156

Pull/Push

Figure 32. Inserting the enclosure

4. Install the two bezel ear caps on the enclosure as follows:

a) Place the left bezel ear cap on the left side of the enclosure and align the mounting holes as shown

in the following figure.

Figure 33. Replacing left ear cap

b) Install the two screws on the rear side of the left bezel ear cap as shown in the following figure.

Figure 34. Displaying left ear cap front view

c) Repeat the above steps to install the right bezel ear cap on the right side of the enclosure.

54 IBM Elastic Storage System 3200: Hardware Planning and Installation Guide

Summary of Contents for Elastic Storage System 3200





























































































































































Search results

Summary of Contents for Elastic Storage System 3200

Reviews:

Related manuals for Elastic Storage System 3200

Brands by name

Popular brands

IBM Elastic Storage System 3200, Hardware Planning And Installation Manual

Search results

Summary of Contents for Elastic Storage System 3200

Reviews:

Related manuals for Elastic Storage System 3200

Brands by name

Popular brands