IBM Elastic Storage System 3200 Hardware Planning And Installation Manual Download Page 114

Page: 114 / 156

# ifconfig interface name

Example:

ifconfig

enP1p8s0f0

Rebooting BMC

There might be situations where the BMC is in a bad state and need to be rebooted. One symptom is when

you run the step to verify the FSP/BMC IP was set correctly in essutils:

Figure 82. EMS

SSR

menu

9. Check FSP interface (EMS or 3200) (HMC1 | BMC)

[root@ess3200rw2b ~]# date;ipmitool lan print 1

Tue Apr 20 08:52:55 MST 2021

No data available

Get Device ID command failed

No data available

No valid response received

No data available

IPMI response is NULL.

Invalid channel: 1

[root@ess3200rw2b ~]#

To fix this issue, do the following:

1. Login as root (password is ibmesscluster).
2. Run the following script:

/opt/ibm/ess/tools/samples/reboot_BMC.sh

You will be prompted for the BMC password (which is the Serial A (left canister) or B (right

canister) and press the Enter key.
Wait for few minutes and confirm the BMC is healthy again by running:

9. Check FSP interface (EMS or 3200) (HMC1 | BMC)

You must get a normal output.

96 IBM Elastic Storage System 3200: Hardware Planning and Installation Guide

Summary of Contents for Elastic Storage System 3200





























































































































































Search results

Summary of Contents for Elastic Storage System 3200

Reviews:

Related manuals for Elastic Storage System 3200

Brands by name

Popular brands

IBM Elastic Storage System 3200, Hardware Planning And Installation Manual

Search results

Summary of Contents for Elastic Storage System 3200

Reviews:

Related manuals for Elastic Storage System 3200

Brands by name

Popular brands