IBM Elastic Storage System 3200 Hardware Planning And Installation Manual Download Page 107

Page: 107 / 156

Figure 80. Close view of IBM Elastic Storage System 3200 Ethernet port LEDs

The following table describes the behavior of Ethernet port LEDs.

Table 26. IBM Elastic Storage System 3200 Ethernet port LEDs
Left LED

Right LED

Behavior

OFF

Indicates no link.

Amber

Green

Indicates link at 100 MBps.

Green

Indicates link at 1000 MBps.

Flashing

Indicates Ethernet link activity.

Server canister status LEDs

The following table describes the possible behavior of server canister status LEDs.

Table 27. Behavior of IBM Elastic Storage System 3200 server canister status LEDs
Canister status OK (Green)

Canister fault (Amber)

Behavior

OFF

The server canister boots and

operates normally.

ON or OFF

A server canister fault is

detected.

OFF

The server canister does not have

any power.

Chapter 5. Monitoring the system using LEDs 89

Summary of Contents for Elastic Storage System 3200





























































































































































Search results

Summary of Contents for Elastic Storage System 3200

Reviews:

Related manuals for Elastic Storage System 3200

Brands by name

Popular brands

IBM Elastic Storage System 3200, Hardware Planning And Installation Manual

Search results

Summary of Contents for Elastic Storage System 3200

Reviews:

Related manuals for Elastic Storage System 3200

Brands by name

Popular brands