IBM Elastic Storage System 3200 Hardware Planning And Installation Manual Download Page 51 | Manualshive

Page: 51 / 156

background image

Table 10. Rack space requirements for the IBM Elastic Storage System 3200

Minimum rail length

Maximum rail depth (including cable management

arm)

685.42 mm (26.98 in.)

830.30 mm (32.69 in.)

Rack installation specifications that are not purchased from IBM

Learn about the requirements and specifications for installing IBM systems into racks that were not

purchased from IBM.
Learn about the requirements and specifications for 19-inch racks. These requirements and specifications

are provided as an aid to help you understand the requirements to install IBM systems into racks. It is

your responsibility, working with your rack manufacturer, to ensure that the rack that is chosen meets the

requirements and specifications that are listed here. Mechanical drawings of the rack, if available from the

manufacturer, are recommended for comparison against the requirements and specifications.
IBM maintenance services and installation planning services do not cover verification of non-IBM

racks for compliance to Power Systems rack specifications. IBM offers racks for IBM products that

are tested and verified by IBM development labs to comply with applicable safety and regulatory

requirements. These racks are also tested and verified to fit and function with IBM products. The

customer is responsible for verifying with the rack manufacturer that any non-IBM racks comply with

IBM specifications.
Note: The 7965-S42 rack meet all the requirements and specifications.
Rack specifications
• The rack or cabinet must meet the EIA Standard EIA-310-D for 19-inch racks published August 24,

1992. The EIA-310-D standard specifies internal dimensions, for example, the width of the rack

opening (width of the chassis), the width of the module mounting flanges, and the mounting hole

spacing.

• The front rack opening must be a minimum of 450 mm (17.72 in.) wide, and the rail-mounting

holes must be 465 mm plus or minus 1.6 mm (18.3 in. plus or minus 0.06 in.) apart on center

(horizontal width between vertical columns of holes on the two front-mounting flanges and on the two

rear-mounting flanges). Figure 1. Rack specifications (top-down view).

Service clearance for IBM Elastic Storage System 3200

The service clearance area is the area around the rack which is needed for the authorized service

representatives to service the enclosure as shown in the sample illustration in the following figures.

Chapter 3. Planning for hardware 33

«
...
49
50
51
52
53
...
»

Summary of Contents for Elastic Storage System 3200





























































































































































Reviews:

No comments

Related manuals for Elastic Storage System 3200

Brand: R/Evolution Pages: 58

DSN-4100 Series

Brand: D-Link Pages: 2

HD080HJ - 80 GB Hard Drive

Brand: Samsung Pages: 2

G2 PORTABLE HX-MU025DC

Brand: Samsung Pages: 36

Brand: Ice-O-Matic Pages: 9

05DTMBAX0307DD-V1

Brand: Mercia Garden Products Pages: 9

Brand: U-Line Pages: 39

Brand: Addonics Technologies Pages: 2

Brand: SanDisk Pages: 7

Brand: LaCie Pages: 24

Maxtor OneTouch 4

Brand: Maxtor Pages: 84

Brand: Magnusson Pages: 18

Brand: HGST Pages: 51

Brand: HP Pages: 1

Brand: Samsung Pages: 5

Brand: Samsung Pages: 10

Brand: Samsung Pages: 10

Brand: Samsung Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands