IBM Elastic Storage System 3200 Hardware Planning And Installation Manual Download Page 73

Page: 73 / 156

Figure 35. Replacing right ear cap

5. Push the enclosure into the rack while pulling the outer rail until the outer and the inner rails lock into

the serviceable position. This is accompanied by an audible click.

6. Press the release tab and push the enclosure fully into the rack.

Release Tab

Figure 36. Release tab

7. Secure the enclosure on the left and right front of the enclosure to the left and right front rack posts by

using the two M5 X 9 shipping screws as shown in the following figure.

Figure 37. Securing the enclosure

At this point, the rails and IBM Elastic Storage System 3200 enclosure are installed. The enclosure is

mounted on the rail with all the components that were removed, reinserted into the slots.

Chapter 4. Installing 55

Summary of Contents for Elastic Storage System 3200





























































































































































Search results

Summary of Contents for Elastic Storage System 3200

Reviews:

Related manuals for Elastic Storage System 3200

Brands by name

Popular brands

IBM Elastic Storage System 3200, Hardware Planning And Installation Manual

Search results

Summary of Contents for Elastic Storage System 3200

Reviews:

Related manuals for Elastic Storage System 3200

Brands by name

Popular brands