IBM Deskstar Deskstar 3 Installation And Reference Manual Download | Manualshive

Page: 48 / 72

background image

41

Partition, format, and copy with IBM DriveGuide Easy Installation Software

Note: You may choose to use Fdisk to partition and format your hard drive. Refer to the section
entitled Fdisk and Format in the Appendix for more information.

Due to system and hard drive variations, the IBM DriveGuide screens displayed may be
different than those presented here.

Note: Many BIOS setups refer to the drives in a system as 0, 1, and so on. IBM DriveGuide
refers to drives as 1, 2, etc.

•

Boot your computer with the IBM DriveGuide diskette in drive A. The IBM
DriveGuide logo is displayed with the message “Loading DriveGuide - Please Wait”.

•

The Welcome screen is displayed. Click “OK”.

Note: If a mouse is not detected, a screen is displayed explaining the use of Tab and Enter to
navigate.

•

A License Agreement is displayed. Click “Accept”.

«
...
46
47
48
49
50
...
»

Summary of Contents for Deskstar Deskstar 3









































































Reviews:

No comments

Related manuals for Deskstar Deskstar 3

Brand: TallyGenicom Pages: 166

Brand: Olivetti Pages: 16

Brand: Oce Pages: 209

Brand: Felix printers Pages: 26

DocuPrint C2535 A

Brand: Xerox Pages: 120

Brand: WANHAO Pages: 60

Brand: Ricoh Pages: 88

Brand: Ricoh Pages: 37

570e - LQ B/W Dot-matrix Printer

Brand: Epson Pages: 18

Brand: Epson Pages: 53

570e - LQ B/W Dot-matrix Printer

Brand: Epson Pages: 2

7800 - Stylus Pro Color Inkjet Printer

Brand: Epson Pages: 176

6200L - EPL B/W Laser Printer

Brand: Epson Pages: 513

Brand: Cembre Pages: 26

Markingenius MG3

Brand: Cembre Pages: 56

890N - FX B/W Dot-matrix Printer

Brand: Epson Pages: 2

Brand: Ricoh Pages: 542

Brand: Toshiba Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands