IBM Deskstar Deskstar 3 Page 18 Installation And Reference Manual Download | Manualshive

Page: 18 / 72

background image

11

Partition and format with IBM DriveGuide Easy Installation Software

Note: You may choose to use Fdisk to partition and format your hard drive. Refer to the section
entitled Fdisk and Format in the Appendix for more information.

Due to system and hard drive variations, the IBM DriveGuide screens displayed may be
different than those presented here.

Note: Many BIOS setups refer to the drives in a system as 0, 1, and so on. IBM DriveGuide
refers to drives as 1, 2, etc.

•

Boot your computer with the IBM DriveGuide diskette in drive A. The IBM
DriveGuide logo is displayed with the message “Loading DriveGuide - Please Wait”.

•

The Welcome screen is displayed. Click “OK”.

Note: If a mouse is not detected, a screen is displayed explaining the use of Tab and Enter to
navigate.

•

A License Agreement is displayed. Click “Accept”.

•

The first screen on the following page appears. The message “Drive 1 is not
formatted” is displayed. Select “Yes” to format the specified drive. Click “No” if the
wrong drive is specified or you want to proceed manually.

«
...
16
17
18
19
20
...
»

Summary of Contents for Deskstar Deskstar 3









































































Reviews:

No comments

Related manuals for Deskstar Deskstar 3

Brand: Unisys Pages: 255

Brand: Xerox Pages: 199

Brand: Oki Pages: 100

Brand: Oki Pages: 2

Brand: Xerox Pages: 316

Brand: Xerox Pages: 74

Brand: Xerox Pages: 306

Brand: Xerox Pages: 16

Brand: Xerox Pages: 4

Brand: Oki Pages: 38

Brand: Oki Pages: 38

Brand: Oki Pages: 36

Brand: Oki Pages: 36

Brand: Datamax Pages: 2

Brand: Xerox Pages: 44

Brand: Oki Pages: 76

Brand: Ricoh Pages: 682

Brand: Roland Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands