IBM Deskstar Deskstar 3 Page 35 Installation And Reference Manual Download | Manualshive

Page: 35 / 72

background image

28

•

Leave the IBM Deskstar jumpers as set. The jumpers are factory set to Master, 16
heads.

•

Set the jumpers on the existing drive for Slave. Refer to the existing drive label or
manual for jumper settings. You may need to remove the existing drive to change the
jumpers.

Note: The IBM Deskstar has an option jumper block located next to the interface connector.
Setting these jumpers allows you to use the different options of the hard disk drive. See the
“Jumpers” section of the Appendix for jumper setting descriptions.

Attach the cables

Note: With some system chassis, it may be more convenient to attach the cable after the drive is
mounted. The order of the following steps may change depending upon your system.

«
...
33
34
35
36
37
...
»

Summary of Contents for Deskstar Deskstar 3









































































Reviews:

No comments

Related manuals for Deskstar Deskstar 3

870 - SuperScript B/W Laser Printer

Brand: NEC Pages: 52

SuperScript 1800

Brand: NEC Pages: 8

Brand: QMS Pages: 208

imagePROGRAF GP-540

Brand: Canon Pages: 82

Brand: Kyocera Pages: 157

Brand: Canon Pages: 521

Brand: Canon Pages: 456

Brand: Axiohm Pages: 8

Brand: Jolimark Pages: 65

Brand: Objet Pages: 122

Brand: Source Technologies Pages: 47

Brand: TonerRefillKits Pages: 10

Brand: Creality Pages: 24

Brand: Jetmobile Pages: 56

Brand: Sam4s Pages: 24

ECP- Magenta Toner Premix/Concentrate for ECP 42

Brand: Xerox Pages: 2

Brand: Canon Pages: 707

Brand: Canon Pages: 339

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands