manualshive.com logo in svg

Hyundai HSL1500T Track, Manual, Page: 72 / 80

Share
Download
Hyundai HSL1500T Track Manual Download Page 72

73

Controls

VEHICLE:

Steering direction and speed controlled by two hand operated control levers.

HYDRAULICS:

Lift and bucket tilt are controlled by separate foot pedals or hand controls.  Auxiliary hydraulics 
controlled by electric solenoid.

ENGINE:

Hand throttle, key type ignition switch and shutoff.

Engine

Make and model ...........................................................................................................................................Kubota V3300-T
Cylinders ................................................................................................................................................................................4
Cooling system ..............................................................................................................................................................Liquid
Displacement .........................................................................................................................................202.5 in³ (3318 cm³)
Horsepower (Gross) ..........................................................................................................................................................87.4
Power (ISO 9249 Net Power) ....................................................................................................................................61.9 kW
Power (ISO 9249 Net Power) CE ..............................................................................................................................61.5 kW
Max Torque....................................................................................................................205 ft. lbs. (280 N m @ 1400 RPM)
Fuel Type...............................................................................................................................................................Diesel No.2
Air Cleaner ................................................................................................................Replaceable Dry Cartridge w/Indicator
Maximum RPM (no load) ................................................................................................................................................2750
Maximum RPM (no load) CE..........................................................................................................................................2500

Hydraulic System

Pump type ........................................................................................................................................................................Gear
Pump Capacity (theoretical) @ 2750 RPM ......................................................................................21.0 GPM (79.5 L/min)
Pump Capacity (theoretical) @ 2500 RPM.......................................................................................19.2 GPM (72.7 L/min)
System Relief Setting .............................................................................................................................3000 PSI (206.8 bar)
Control Valve ........................................................................................Series type with float on lift and electrical auxiliary
Filtration ....................................................................................................................................................................5 Micron
Hydraulic Fluid......................................................................................................................................10W30 API Class, SJ
Oil Cooler ......................................................................................................................................1250 BTU/min (315 kCal)
Cylinders. ....................................................................................................................................Lift

Tilt

Type.............................................................................................................................Double acting

Double Acting

Qty- per mach  ........................................................................................................................2

2

Bore dia  ................................................................................................................................3 in.

3 in.

Rod dia ...................................................................................................................................2 in.

2 in.

Stroke .................................................................................................................................27.9 in.

15.5 in.

Hydrostatic Transmission & Final Drive:

Pump type .............................................................................................................................Two in line, axial piston pumps
Pump displacement  ....................................................................................................................................2.80 in³ (46 cm³)
Motor type  .........................................................................................................................................................Radial Piston
Motor displacement (Low)........................................................................................................................45.8 in³ (750 cm³)
Motor Displacement (High) ......................................................................................................................24.9 in³ (408 cm³)
System relief setting  .................................................................................................................................5000 PSI (345 bar)
Final drive (Wheel Loaders) ...................................................................Single roller chain running in oil bath to each axle
Final Drive (Track Loaders) ...................................................................Double roller chain running in oil bath to rear axle
Drive chain size (Wheel Loaders) .........................................................................................................................ASA 100H
Drive chain size (Track Loaders) ........................................................................................................................ASA 100H 2

5.  SPECIFICATIONS

Summary of Contents for HSL1500T Track

















































































Reviews:

No comments