HySecurity StrongArmPark DC Page 84 Programming And Operations Manual Download

Page: 84 / 96

rIve

elt

ensIon

and

lIgnment

Proper drive belt tension is important for prolonging the life of the drive belt and maintaining the superior

performance of the operator. To check the drive belt tension, take the following steps:

1.  Remove the Front Access Panel.
2.  Turn off the AC and DC power switches.
3.  Remove the StrongArmPark DC top cover and drive belt cover.
4.  Check to make sure the pulleys are aligned vertically.
5.

With your finger, apply light outward pressure

to the drive belt. If it is properly tensioned, it

should only move about

Z\zn

Z\,

-inch (1.6 to

3.2 cm).

6. To replace or re-tension the drive belt. Loosen

the four motor bracket nuts and move the
motor accordingly.

7.  Retighten the motor bracket nuts.
8.  Replace the drive belt cover and top cover.
9.  Turn the AC and DC power switches ON. This

cycles power which allows the operator to

search for the target magnet and “relearn”
its limits.

NOTE:

Be aware that the arm will cycle open, and then

close, as it relearns its limits. If you don’t cycle the power,
the operator will not “relearn” its limits and will not operate properly.

DC and AC

power switches

Top cover

Drive belt

cover

Front access panel

LTR

Z\zn

Z\,

-inches

(1.6 to 3.2 mm)

Motor bracket nuts

Pulley

MX3650-01 Rev. D

StrongArmPark DC Programming & Operations

www.hysecurity.com

Summary of Contents for StrongArmPark DC

































































































Search results

Summary of Contents for StrongArmPark DC

Reviews:

Related manuals for StrongArmPark DC

Brands by name

Popular brands

HySecurity StrongArmPark DC, Programming And Operations Manual

Search results

Summary of Contents for StrongArmPark DC

Reviews:

Related manuals for StrongArmPark DC

Brands by name

Popular brands