HySecurity StrongArmPark DC Page 5 Programming And Operations Manual Download | Manualshive

Page: 5 / 96

background image

StrongArmPark DC Installer CheckList

The following list provides a high level overview of the tasks involved in installing the StrongArmPark DC gate

operator. Take a moment to review the list and check off the items as you complete the install.

Site Prep - concrete pad location/dimensions. Use template printed on the side of the sipping box.

Make sure gate installation complies with ASTM F2200 Standard Specification for Automated Vehicular

Gate Construction. And, install the supplied WARNING signs on both sides of the barrier arm and on

its chassis. Signs must be viewable by incoming and outgoing vehicular traffic.

Check for compliance with local codes, site conditions, and NEC standards.

Install gate operator - (on concrete pad use four ½ - 13 x 3.5in long concrete wedge anchors.)

Connect AC Power.

Connect red wire to DC Power Switch.

Turn DC Power ON.

Connect all accessory devices.

Check the Smart DC Controller software version. If necessary, upload the latest version from

www.hysecurity.com

. See Smart Touch Analyze and Retrieve Tool.

Set the Close Timer (through the User Menu).

Set barrier arm speed, if applicable (through Installer Menu). Refer to S.T.A.R.T. (Smart Touch Analyze

and Retrieve Tool) in the Reference section.

Set the dynamic reversing sensitivity, if needed (through Installer Menu).

Set Relay User 2 to 28 or 29 and BA to 1 (breakaway arm) in the Installer Menu.

Configure changes through the Installer Menu depending on the accessory devices that you have

installed.

Give a copy of the Important Safety Information and pertinent operator instructions to the end user.
Show the end user how to:

•  Remove the barrier arm from the breakaway bracket.
•  Turn the power off and on to demonstrate learn limits after DC/AC cycles.
•  Adjust physical limit stops for barrier arm open and close positioning.
•  Turn the DC power switch off, which disengages the motor, and manually lift the barrier arm open.

Take photographs of the completed installation site and save it in your business files.

www.hysecurity.com

© 2017

Introduction

MX3650-01 Rev. D

v

«
...
3
4
5
6
7
...
»

Summary of Contents for StrongArmPark DC

































































































Reviews:

No comments

Related manuals for StrongArmPark DC

Brand: CAME Pages: 12

Brand: TdA Pages: 19

Brand: PPA Pages: 2

Brand: PowerTech Pages: 16

Brand: PowerTech Pages: 20

Brand: GDS Pages: 11

Brand: USAutomatic Pages: 76

Brand: decakila Pages: 8

Brand: FlexiForce Pages: 16

AccessMaster M885

Brand: Chamberlain Pages: 36

Estate Swing E-SC 1102 Series

Brand: FAAC Pages: 38

Brand: CAB Pages: 13

Brand: Jaytech Pages: 19

Brand: RIB Pages: 32

655502 "Single"

Brand: Chamberlain Pages: 2

Brand: Turnstyle Pages: 20

Brand: Ovente Pages: 8

Brand: Black+Decker Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands