HySecurity StrongArmPark DC Page 48 Programming And Operations Manual Download

Page: 48 / 96

Parking Site Use

The label for the

Smart DC Controller

accommodates

arming loops and

establishes which

open commands need

to be wired for vehicle

counts (transient,

special, and tenant

“user types”).

The software identifies

the access control

inputs and uses the

arming loops to

control relay and

network outputs.

COM

COM
COM

STOP
OPEN

RADIO

OPEN

PARTIAL

SENSOR 1

EXIT

LOOP
BLOCK

EXIT

IN OBS

LOOP

OUT OBS

LOOP

CENTER

LOOP

+ 24 V
EMERG

OPEN

SHOW

LEDs

RADIO OPTIONS

+24V

OPEN

COM

DUAL GATE

COM

COM NO

COMMON

TERMINALS

RS-485

COMMUNICATION

USB PORT

USER RELAY 1

Electro-mechanical

USER RELAY 2

Solid state

24VDC

12VDC

Access controls

Radio receiver

(Ex. Card reader, keypad)

Red LED

heart

beat

indicates

processor is

working.

Mul�-colored LED

indicates power and gate

status.

RS-232

Press bu�on to light

ac�ve inputs.

Ethernet

expansion

24VDC

24VAC

12VDC

EXIT

LOOP

INSIDE LOOP

(Inner Arming

Loop)

LOOP

Not to Scale

SENSOR 3

SENSOR 2

SENSOR

COM

OUTSIDE LOOP

(Outer Arming

Loop)

CENTER LOOP

Two power

supplies (2

terminals each)

are available

for peripheral

connections:

24VDC & 12VDC

NOTE:

Each

power supply

(and its

corresponding

terminals) can

be used in any

combination to

draw the available

1A maximum.

Hy5B

onneCtIng

CCessorY

evICes

Devices, such as gate edge sensors and photoelectric beams, must be installed to protect against entrapment.

These secondary entrapment protection devices are required for the gate installation to be in compliance with

UL 325 Safety Standards. Most Crash gates are site-specific when it comes to safety standard compliance, and

power requirements fall under UL 508A. Always check your local area codes and comply with all regulations.

Standard accessory (entrapment and loop wire) connections are shown in the following illustration. All

accessories require a minimum of two connections:

• a device input
• a Common Bus Terminal (COM)

TRANSIENT

USER

SPECIAL

USER
TENANT

USER

SPARE

EYE

CLOSE
EXIT

LOOP

BLOCK

EXIT

INNER

ARMING
OUTER

ARMING

NOTE:

The most current software must be loaded on

your Smart DC Controller and the operator identified as

OT 14 for the Parking Site labeled inputs to be effective.

MX3650-01 Rev. D

StrongArmPark DC Programming & Operations

www.hysecurity.com

Summary of Contents for StrongArmPark DC

































































































Search results

Summary of Contents for StrongArmPark DC

Reviews:

Related manuals for StrongArmPark DC

Brands by name

Popular brands

HySecurity StrongArmPark DC, Programming And Operations Manual

Search results

Summary of Contents for StrongArmPark DC

Reviews:

Related manuals for StrongArmPark DC

Brands by name

Popular brands