HySecurity StrongArmPark DC Page 12 Programming And Operations Manual Download | Manualshive

Page: 12 / 96

background image

n

otICes

and

B

ulletIns

Installers should visit HySecurity’s online Technical Support page at www.hysecurity.com or contact HySecurity

prior to installing product to make sure they have received the most up-to-date information.

s

upplemental

d

oCuments

The product literature is comprehensive and contains information needed to plan, install, operate and maintain

your gate operator. Additional general information concerning HySecurity gate operators can be obtained
from the following:

•

HySecurity web site www.hysecurity.com - Contains links to the product catalog, product order

form, operator manuals, operator software downloads, technical support bulletins and other useful

information.

•

S.T.A.R.T. - Smart Touch Analyze and Retrieve Tool - User’s Guide (D0049) detailing the extensive

software, diagnostic and troubleshooting capabilities of the Smart DC Controller board.

•

Technical Bulletins (as applicable).

NOTE:

Technical Bulletins are automatically issued to registered users of HySecurity products. The product warranty registration

card can be filled out online at www.hysecurity.com.

H

azardous

m

aterIals

and

p

roper

d

Isposal

Be aware of the international, federal, and local codes in your area and how best to handle hazardous waste

materials.

The pump pack fluid, found in all hydraulic HySecurity operators, can be recycled. Gear oil, found in HySecurity
electromechanical gate operators, can also be recycled. If the fluids are mixed or contaminated with any

solvents or other chemicals, they become hazardous waste. Hazardous waste requirements for storage and

disposal must be followed.

CAUTION

If the gate operator has a battery backup system, the batteries contain materials that are considered hazardous
to the environment. Proper disposal of the battery is required by federal law. In the U.S.A., refer to federal EPA
guidelines for proper hazardous waste disposal.

2

MX3650-01 Rev. D

StrongArmPark DC Programming & Operations

© 2017

www.hysecurity.com

«
...
10
11
12
13
14
...
»

Summary of Contents for StrongArmPark DC

































































































Reviews:

No comments

Related manuals for StrongArmPark DC

Brand: Vector Pages: 54

Brand: Vector2 Pages: 52

Brand: Calimet Pages: 21

Brand: Calimet Pages: 16

Brand: V2 Pages: 29

Brand: White Rose Pages: 29

Brand: Omker Pages: 6

Brand: Wayne-Dalton Pages: 22

Brand: Linear Pages: 3

Brand: DITEC Pages: 16

Brand: Chamberlain Pages: 40

Brand: Nice Pages: 11

Brand: Nice Pages: 28

Controll-A-Door Advance SDO-2V2 Tri-Tran+

Brand: B&D Pages: 20

Brand: SEA Pages: 8

Brand: E.T. Systems Pages: 30

Brand: tau Pages: 44

Brand: USAutomatic Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands