Hydac OF5 CM Operating And Maintenance Instructions Manual Download Page 72

Page: 72 / 80

Table of Illustrations

HYDAC FILTER SYSTEMS GMBH

72 / 80

BeWa OF5 CM 3580053c en-us print

Table of Illustrations

Fig. 1

Overview / labeling of the title page .........................................................

Fig. 2

Fire protection class B ..............................................................................

Fig. 3

Minimum distance for fire fighting.............................................................

Fig. 4

Checking the scope of delivery ................................................................

Fig. 5

Dimensions...............................................................................................

Fig. 6

Hydraulic diagram ....................................................................................

Fig. 7

Decoding the name plate .........................................................................

Fig. 8

Model code OF5CM .................................................................................

Fig. 9

Components/operating elements .............................................................

Fig. 10

Transporting the OF5 F/L .........................................................................

Fig. 11

Avoiding siphoning ...................................................................................

Fig. 12

Measure dynamic pressure or differential pressure .................................

Fig. 13

Pressure loss formula...............................................................................

Fig. 14

Operating mode Circulation pumping with filtration ..................................

Fig. 15

Filtration to the cleanliness class operating mode....................................

Fig. 16

Operating mode Circulation pumping with filtration ..................................

Fig. 17

Filtration to the cleanliness class operating mode....................................

Fig. 18

Operating mode Circulation pumping without filtration .............................

Fig. 19

Filtration to the cleanliness class operating mode....................................

Fig. 20

Observe the optical clogging indicator .....................................................

Summary of Contents for OF5 CM

















































































Search results

Summary of Contents for OF5 CM

Reviews:

Related manuals for OF5 CM

Brands by name

Popular brands

Hydac OF5 CM, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for OF5 CM

Reviews:

Related manuals for OF5 CM

Brands by name

Popular brands