manualshive.com logo in svg

Hydac OF5 CM, Operating And Maintenance Instructions Manual

Share
Download
Hydac OF5 CM Operating And Maintenance Instructions Manual Download Page 40

5 | Setting up / assembly / integration of the filter unit

HYDAC FILTER SYSTEMS GMBH

40 / 80

BeWa OF5 CM 3580053c en-us print

5.4 Making the electrical connections

Depending on the version, the filter unit has different drive mo-
tors (different voltage / output / number of phases, etc.). Follow
the instructions in the next section to electrically connect the fil-
ter unit.

The IP protection class of the power plug installed on the
productcan vary from the IP protection class of the entire
product, see 

IEC DIN EN 60204-1

, Chapter 7.2.2.

If you require a power plug with a higher IP protection class,
exchange this one for a suitable power plug. Exchanging the
power plug has no effect on the validity of the CE declaration
of conformity of the entire product.

5.4.1 Connecting the filter unit with 1 phase electric

motor

For the version with a single-phase electric motor, the filter unit
is supplied ready for connection with a power plug.

1.

Remove the connector cable from its holder and unwind
it completely.

2.

Before plugging in the power plug, make sure that the
main switch is in the 

0

 or 

OFF

 position.

3.

Check that the voltage and frequency are correct. You
will find the filter unit's electrical data on the electric mo-
tor's name plate.

4.

Plug the power plug into a suitable power outlet.

5.

Switch the filter unit on or off at the main switch.

Depending on the version, the filter unit has thermal protection
in the motor windings and a motor protection switch in the ter-
minal box to protect it from electrical overload.

1

2

3

4

5

6

7

8

9

Summary of Contents for OF5 CM

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands