HYDAC FILTER SYSTEMS FCU 2000-4 Series Operating And Maintenance Instructions Manual Download Page 8

 

Preface 

 

Preface 

These operating  instructions were made to the best of our knowledge. 

Nevertheless and despite the greatest care, it cannot be excluded that 

mistakes could have crept in. Therefore please understand that, in the 

absence of any provisions to the contrary hereinafter, our warranty and 

liability – for any legal reasons whatsoever – are excluded in respect of the 

information in these operating instructions. In particular, we shall not be liable 

for lost profit or other financial loss. 
This exclusion of liability does not apply in cases of intent and gross 

negligence. Moreover, it does not apply to defects which have been 

deceitfully concealed or whose absence has been guaranteed, nor in cases 

of culpable harm to life, physical injury and damage to health. If we 

negligently breach any material contractual obligation, our liability shall be 

limited to foreseeable damage. Claims due to Product Liability shall remain 

unaffected. 
 

Technical Support 

If you have any questions, suggestions, or encounter any problems of a 

technical nature, please don't hesitate to contact us. When contacting us, 

please always include the model code, serial no. and part no. of the product: 
Fax: 

+49 6897 509 9046 

E-mail: 

[email protected] 

 

Modifications to the Product 

We would like to point out that changes to the product (e.g. purchasing 

additional options, etc.) may mean that the information in the operating 

instructions is no longer applicable or adequate. 
After modification or repair work that affects the safety of the product has 

been carried out on components, the product may not be returned to 

operation until it has been checked and released by a HYDAC technician. 
Please notify us immediately of any modifications made to the product 

whether by you or a third party. 
 

Warranty 

For the warranty provided by us, please refer to the terms of delivery of 

HYDAC FILTER SYSTEMS GMBH. 
You will find these under www.hydac.com -> Legal information. 
 

FCU 2000-4 series 

en(us) 

8 / 120 

BEWA FCU2000-4 3109987h en-us 2017-01-24.docx 

2017-01-24 

 

Summary of Contents for FCU 2000-4 Series

























































































































Reviews: