manualshive.com logo in svg

HYDAC FILTER SYSTEMS FCU 2000-4 Series, Operating And Maintenance Instructions Manual

Share
Download
HYDAC FILTER SYSTEMS FCU 2000-4 Series Operating And Maintenance Instructions Manual Download Page 47

 

FCU menus 

 

MODE "M4:: Filter from to" (performance of automatic filtration) 

MODE M4 "Filter from ... to..." enables the FCU to assume control of an 

external filtration unit (e.g. OF5C). The external filtration unit will be controlled 

thereby in such a way that the oil cleanliness in the tank to be monitored will 

always

 be within the specified limits. 

If the lower limit value is reached or if it is not met, then the FCU will switch 

off the unit to be actuated and the test cycle time begins. After the test cycle 

time has elapsed, the FCU carries out a testing measurement (100 ml) and 

checks whether the measured values lie within the limit values. If "yes", then 

the test cycle time begins again; if "no", then the device is switched on in 

order to filter the fluid. 
If the test cycle time setting is below LIMITS 0 [min], then this function is 

switched off. 
Typical applications: 

Long-term monitoring and filtration of the oil 

cleanliness in hydraulic systems and 

documentation thereof via an online printout. 

 

MODE "M5: Measure Autostop" 

MODE M5 "Measure autostop" enables the number (1 to 100) of single 

measurements to be programmed via the FCU’s high-pressure port, after 

which measurement operation is concluded automatically.When online 

printing is activated, the result of the last measurement is additionally 

outputted in the form of particle counts (absolute value). 
Typical applications: 

Routine analysis of the cleanliness of a hydraulic 

system using a defined number of measurements. 

 

MODE "M6: Autostop pump" 

MODE M6 "Autostop pump” enables the number (1 to 100) of single 

measurements to be programmed via the FCU’s suction inlet, after which 

measurement operation is concluded automatically. 
The integrated pump starts up when the OK/START button is pressed. 
The first measurement begins immediately after the set start delay. 

(The start delay is used to air-bleed and rinse the FCU) 
When online printing is activated, the result of the last measurement is 

additionally outputted in the form of particle counts (absolute value). 
Typical applications: 

Gauging the oil cleanliness of a tank or an oil 

sample. 

 

FCU 2000-4 series 

en(us) 

47 / 120 

BEWA FCU2000-4 3109987h en-us 2017-01-24.docx 

2017-01-24 

 

Summary of Contents for FCU 2000-4 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands