HYDAC FILTER SYSTEMS FCU 2000-4 Series Operating And Maintenance Instructions Manual Download Page 28

Page: 28 / 120

FCUElectrical connection

FCUElectrical connection

The FCU is equipped with a battery. This allows network-independent

measurement (with online printout) of approx. 5 hours and measurements

with internal pump: viscosity-dependent of approx. 2 hours.
The battery is automatically recharged when the power adapter is plugged in,

regardless of whether the FCU is switched on or off at the switch or not.

Connecting "POWER INPUT"

Insert the hollow plug on the supplied power adapter into the rear bushing

"POWER INPUT". Switch on the FCU on or off at the On/Off switch on the

rear side.
This connection is used for supplying the FCU electronics and battery

charging circuit with power.

FCU 2000-4 series

en(us)

28 / 120

BEWA FCU2000-4 3109987h en-us 2017-01-24.docx

2017-01-24

Summary of Contents for FCU 2000-4 Series

























































































































Search results

Summary of Contents for FCU 2000-4 Series

Reviews:

Brands by name

Popular brands

HYDAC FILTER SYSTEMS FCU 2000-4 Series, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for FCU 2000-4 Series

Reviews:

Brands by name

Popular brands