Husqvarna K 1260 Workshop Manual Download | Manualshive

Page: 4 / 55

background image

MODELS

4

K1260

This is the basic model of the K1260 and is
available for blade diameters 14 ˝ (350 mm)
and 16 ˝ (400 mm). The machines are com-
pletely identical except for the blade guard
size.

K1260 Rail

This is a special version of K1260, which is
designed for track cutting, together with the
fixture RA10.

K1260 Rail has a custom front bearing

housing with connection for the track cutting
fixture. The blade guard is chrome plated to
withstand high temperatures. The blade guard
has no kit for wet cutting.

The Rail version is also available for blade

diameters 14˝ (350 mm) and 16˝ (400 mm).
The blade guard, belt pulleys and front belt
guard are different for the 14 and 16 inch
versions.

2

RA 10

K 1260

K 1260 Rail

«
...
2
3
4
5
6
...
»

Summary of Contents for K 1260
























































Reviews:

No comments

Related manuals for K 1260

Brand: IDEAL Pages: 52

Brand: Dahle Pages: 32

Brand: Metabo Pages: 55

Brand: Zenoah Pages: 62

Brand: Ioline Pages: 5

Brand: Stanley Pages: 7

PAPER ROLL CUTTER

Brand: DIY CREW Pages: 3

Brand: Current Tools Pages: 10

Brand: Zipper Mowers Pages: 13

Micro Cross Cut PS600-75

Brand: Peach Pages: 18

Brand: Solo Pages: 132

Brand: BROWN Pages: 40

Brand: Zenoah Pages: 16

Brand: Zenoah Pages: 36

Brand: Zenoah Pages: 13

Powerplus POWDPG7551

Brand: VARO Pages: 14

Brand: Lawn-King Pages: 34

Brand: Bush Hog Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands