manualshive.com logo in svg

Husqvarna 4421-DXL, User Manual

The Husqvarna 4421-DXL is a top-of-the-line chainsaw designed for both professional and residential use. With its powerful engine and durable construction, this chainsaw ensures optimal performance and longevity. To get the most out of this exceptional tool, make sure to download the comprehensive Owner's Manual for free at manualshive.com.

Share
Download
background image

Using A Booster Battery (Jump Starting)

WARNING

• Wear safety glasses or approved eye protection when servicing the vehicle. Wear a full face shield and

rubber gloves when working on or near batteries.

5.

Carefully check the electrolyte level and add distilled water if necessary. Do not fill the battery cells above
the designated fill line. Replace battery cell caps.

6.

Clean both battery terminals with a solution of baking soda and water (1 cup (237 mL) baking soda per 1 gallon
(3.8 L) of water). Rinse thoroughly. Do not allow this solution to enter the battery. Tighten battery terminals to 144
in-lb (16 N·m). Let the terminals dry and then spray them with Battery Terminal Protector Spray (P/N 603 00
00-03).

See following WARNING.

WARNING

• If battery wire terminals are damaged or corroded, replace or clean them as necessary. Failure to do

so may cause them to overheat during operation and could result in a fire, property damage, or
personal injury.

Be sure the battery hold-down clamp is properly tightened. Tighten to 108 in-lb (12.2 N·m). A loose clamp may allow
the battery to become damaged from vibration or jarring.

If battery appears weak, have it charged by a trained technician. The battery should never be left discharged any
longer than absolutely necessary (do not leave discharged overnight).

USING A BOOSTER BATTERY (JUMP STARTING)

WARNING

• Wear safety glasses or approved eye protection when servicing the vehicle. Wear a full face shield and

rubber gloves when working on or near batteries.

• When jumping from a booster battery make final connection (negative) at engine frame.

• Do not jump start or charge a frozen or damaged battery. Unplug charger before connecting or

disconnecting cables to the battery. Never lean over battery while boosting, testing, or charging.

If it is necessary to use a booster battery to start the engine, BE CAREFUL!

1.

Turn the key switch to the OFF position. Place the Forward/Reverse handle in the NEUTRAL position, engage
the park brake, and chock the wheels.

2.

Ensure the booster battery is 12-volt.

See following NOTE.

NOTE:

A starting battery is recommended but a deep cycle battery can be used if necessary.

3.

Access the engine compartment by raising the cargo bed.

See WARNING “For vehicles with cargo beds...” in

General Warnings on page 11.

4.

Locate the vehicle battery on the driver’s side of the vehicle under the cargo bed

(Figure 39)

.

5.

Connect the end of the first cable (1) to the positive (+) terminal of the booster battery. Connect the other
end of the same cable (2) to the positive terminal of the vehicle battery.

See DANGER “Battery – Explosive

gases!...” in General Warnings on page 11.

6.

Connect the end of the second cable (3) to the negative (–) terminal of the booster battery. Connect the other end
of the same cable (4) to the battery frame ground.

7.

Sit in the driver’s seat and start the engine.

8.

After the engine has started, remove the frame ground (–) cable (4) first. Remove the cable from the positive
terminal (2). Then remove the cables from the booster battery.

See following CAUTION.

Page 52

HUV 4421 Owner’s Manual

Summary of Contents for 4421-DXL





































































Reviews:

No comments

Related manuals for 4421-DXL

BRP LYNX RADIEN UTILITY ACE 2022 Series Operator'S Manual preview
LYNX RADIEN UTILITY ACE 2022 Series
Brand: BRP Pages: 252
Snapper UV1621BV Parts Manual preview
UV1621BV
Brand: Snapper Pages: 82
TransTank GlidePath Operator'S Handbook Manual preview
GlidePath
Brand: TransTank Pages: 28
Eton DXL90 Owner'S Manual preview
DXL90
Brand: Eton Pages: 30
Strautmann Giga-Trailer 1840 Operating Instructions Manual preview
Giga-Trailer 1840
Brand: Strautmann Pages: 39
Etnyre Centennial A-130-12R Manual preview
Centennial A-130-12R
Brand: Etnyre Pages: 20
HYOSUNG TE 50 Owner'S Manual preview
TE 50
Brand: HYOSUNG Pages: 48
Can-Am 2008 Outlander 400 EFI Shop Manual preview
2008 Outlander 400 EFI
Brand: Can-Am Pages: 599
Erde SY150 Assembly Instructions preview
SY150
Brand: Erde Pages: 4
Polaris 2009 Ranger RZR 800 EFI Manual preview
2009 Ranger RZR 800 EFI
Brand: Polaris Pages: 332
Tao Motor D125 Owner'S Manual preview
D125
Brand: Tao Motor Pages: 73
Baja WD400U Service Manual preview
WD400U
Brand: Baja Pages: 180
Landoll LT10A Series Operator'S Manual preview
LT10A Series
Brand: Landoll Pages: 36
Dazon Raider Max 175S Owner'S Manual preview
Raider Max 175S
Brand: Dazon Pages: 54
Dazon Raider mini 90S Service Manual preview
Raider mini 90S
Brand: Dazon Pages: 60
Yamaha YFM4FAR Service Manual preview
YFM4FAR
Brand: Yamaha Pages: 397
Agri-Fab 45-01004 Owner'S Manual preview
45-01004
Brand: Agri-Fab Pages: 12
Yamaha VT500B Owner'S Manual preview
VT500B
Brand: Yamaha Pages: 112

Brands by name

Popular brands

Load more brands