Husqvarna 4421-DXL User Manual Download Page 36

Page: 36 / 68

Periodic Service Schedule

PERIODIC SERVICE SCHEDULE

REGULAR INTERVAL

SERVICE

Pre-Operation and Daily Safety Checklist

See Pre-Operation and Daily Safety

Checklist on page 22.

Daily service by owner

Performance Inspection

See Performance Inspection on page 23.

Check engine oil level; add if necessary.

See

Engine Oil Level Check on page 39.

Engine

Diesel vehicles:

Check engine coolant; add if

necessary.

See Engine Coolant Level Check

on page 46.

Fuel filters

Diesel vehicles:

Drain water from fuel filter.

See Draining Water from Fuel Filter on

page 49.

Daily service by owner or trained technician

Brakes

Check brake fluid; add if necessary. Check

brake pedal for proper operation.

See

Performance Inspection on page 23.

Engine

Check engine circulating air passage; visually

inspect unshrouded area around engine

exhaust for grass and debris and clean if

necessary.

Diesel vehicles:

Check for grass

and debris around the radiator.

Tires

Check air pressure and adjust if necessary.

See Vehicle Specifications on page 56.

Transmission and differentials

Check lubricant levels. Add if necessary.

See Lubrication Level Check for Front

Differential, Transmission, and Rear

Differential on page 44.

Monthly service by owner or trained

technician

General vehicle

Wash engine compartment and underside of

vehicle. Do not wash engine when hot.

Battery

Clean terminals and wash dirt from casing;

check electrolyte level. Add distilled water if

necessary.

See page 50.

Front wheel alignment and toe-in

Check and adjust if necessary.

See Steering

and Front Suspension Section in the

appropriate maintenance and service

manual.

Electrical wiring and connections

Check for tightness and damage.

Inspect master cylinder, brake lines, and hoses

for damage or leakage.

Check park brake cables for damage; replace

if necessary.

Semiannual service by trained technician

only (or every 50 hours of operation,

whichever comes first)

Brake system

Check brake pads and discs; replace if

necessary.

For brake wear-in procedure,

see Hydraulic Brakes in the Pre-Operation

and Daily Safety Checklist on page 22.

See also Brake System Section in the

Page 34

HUV 4421 Owner’s Manual

Summary of Contents for 4421-DXL





































































Search results

Summary of Contents for 4421-DXL

Reviews:

Related manuals for 4421-DXL

Brands by name

Popular brands

Husqvarna 4421-DXL, User Manual

Search results

Summary of Contents for 4421-DXL

Reviews:

Related manuals for 4421-DXL

Brands by name

Popular brands