Husqvarna 4421-DXL User Manual Download Page 50

Page: 50 / 68

Fueling Instructions

FUELING INSTRUCTIONS

See General Warnings on page 11.

DANGER

• Turn the key switch to the OFF position before fueling.

• Do not pour fuel into the fuel tank when the engine is hot or while it is running.

• To avoid electric arc caused by static electricity, the fuel storage/pumping device must be grounded. If

the pump is not grounded, the vehicle must be grounded to the pump before and during the fueling
operation.

• To avoid the possibility of fire, clean up any spilled fuel before operating the vehicle.

Remove the fuel cap and fill the tank with fuel. Gasoline vehicles have a black fuel cap; diesel vehicles have a
green fuel cap.

See preceding DANGER and following NOTE.

NOTE: Gasoline vehicles:

Use unleaded gasoline only. Whenever possible, avoid using oxygenated fuels and fuels

that are blended with alcohol.

Diesel vehicles:

Use only diesel fuel grade no. 2 with a cetane rating of 45 or higher.

Replace the fuel cap. Ensure that the cap is tightened securely.

Clean any spilled fuel from the cap or around the fuel cap area.

219

Figure 34

Fuel Tank – Gasoline Vehicles

220

Figure 35

Fuel Tank – Diesel Vehicles

BIODIESEL FUEL (DIESEL VEHICLES ONLY)

Biodiesel has unique qualities that should be considered before it is used in the Kubota D722 diesel engine. During
cold weather, plugged fuel lines, plugged fuel systems, hard starting, and other unknown failures can result from use
of this fuel.

Page 48

HUV 4421 Owner’s Manual

Summary of Contents for 4421-DXL





































































Search results

Summary of Contents for 4421-DXL

Reviews:

Related manuals for 4421-DXL

Brands by name

Popular brands

Husqvarna 4421-DXL, User Manual

Search results

Summary of Contents for 4421-DXL

Reviews:

Related manuals for 4421-DXL

Brands by name

Popular brands